Hp printer stuck on initializing

Please go through the steps in this document to make sure everything setup properly. Here is the link: Setting Up the Printer Hardware for HP Color LaserJet Pro M177fw MFP Printers. You can manually move the carousel for the toners, if it is stuck. Open the scanner lid and the lid below that so you should see the toners.

6,370. New member. 09-07-2021 04:31 AM. Product: M507dn. Operating System: Microsoft Windows 10 (64-bit) My M507 came out of sleep mode last night to print and went to a screen saying initalizing with a number counting up. I left it in the over night and it's still counting up.HP Support Agent. 03-07-2022 12:41 PM. @firebabeee. Welcome to the HP support community. I understand that your printer is stuck in initializing the screen, I am glad to assist you. You might have to reset the printer. I am sending you a private message with the steps to reset the printer.a. Unplugged the power cable from the printer and wall outlet for 60 seconds. b. Reconnected the power cable to the printer and wall outlet. c. Issue remains. 2. Performed a power drain. a. Disconnected the power cord from the back of the printer, power button pressed for 30 seconds with the switch in ON position for 30 seconds.Upon start up, as soon as the screen shows the HP logo (at this point, in black and white), press and hold, in the touch screen area only, the area just above the question mark, until the "...init" prompt appears, then release. This reset procedure will reboot the printer and take it back to READY state. larreaza. 6 0 0.Level 13. 05-24-2023 01:25 PM. The first step would be to turn the printer OFF and disconnect the ethernet cable from the printer. Turn the printer ON without ethernet to see if will it boot to Ready. If that doesn't help cold reset is the next step.Jan 20, 2017 · Restore printer to factory defaults: * On the product control panel, touch the Setup button. * Scroll to and touch the Service menu. * Scroll to and touch the Restore Defaults button, and then touch the OK button. The product automatically restarts. 7. Turn Off the printer for 3 min and then try turning On the unit. May 22, 2022 · Hello, Below listed steps should fix the issue. Turn the printer on, if it is not already on. Wait until the printer is idle and silent before you continue. With the printer turned on, disconnect the power cord from the rear of the printer. Unplug the power cord from the wall outlet. Wait at least 60 seconds.

May 20, 2023 · 05-20-2023 12:49 PM. Product: HP ENVY Photo 7855 All-in-One Printer. Hi, I have an HP Envy 7855, and like others, have tried all of the suggested and/or recommended troubleshooting steps. I use this printer for work & am not in a position to purchase another one. The web page offers eight easy ways to solve the issue of HP printer stuck on initializing error, such as unplugging the power case, updating the printer driver, performing a hard reset, and reaching out for a technician. It also explains the reasons and steps for each method, with screenshots and links to more resources.Here are the reset steps: For Printer that has Touch control panel Bundled. Turn off the device. Press and hold the lower right quadrant of the touch screen, keep the quadrant depressed as you turn the product on. When the ‘Permanent Storage Init.’. Message appears on the display, release the button.Here are the reset steps: For Printer that has Touch control panel Bundled. Turn off the device. Press and hold the lower right quadrant of the touch screen, keep the quadrant depressed as you turn the product on. When the ‘Permanent Storage Init.’. Message appears on the display, release the button.HP M477 fdw, stuck on Initializing i have replaced. Scanner, formatter board Permanent initialized and no luck any help will be highly appreciated - 9004638 ... Check out this link: HP printer is offline or unavailable. Jljesus3. 1 0 0 54 New member ‎02-27-2024 12:01 PM. HP Recommended. Mark as New; Bookmark; Subscribe; Permalink; …I read your HP LaserJet Pro MFP M225dn Printer is stuck on initialization. I would like to help you resolve this issue. Perform a Hard Reset on the printer. Remove the power cable from the printer when it is turned on. Press and hold the power button for 60secs. Connect the power cable to printer and directly to wall outlet. Turn on the printer.5. Perform a power drain by disconnecting the power cord from the back of the printer and keeping the power button pressed for 30 seconds and if there is a power switch, keep the switch in ON position for 30 seconds before reconnecting the power cord. 6. Turn Off the printer for 3 min and then try turning on the unit.

If you turn it back on it starts up and gets stuck initializing again. The printer is brand new and under warranty. FYI I have already tried the following steps -. Step #1 - Remove device from devices and printers if it exists. Step #2 - Pull power cable out of the back while printer is running. * With the printer turned on, disconnect the ...Here are the reset steps: For Printer that has Touch control panel Bundled. Turn off the device. Press and hold the lower right quadrant of the touch screen, keep the quadrant depressed as you turn the product on. When the ‘Permanent Storage Init.’. Message appears on the display, release the button.<link rel="stylesheet" href="/wcc-assets/styles.c835227603fb7258.css">If you have recently purchased an HP printer, the first thing you need to do is install the printer drivers. Without the proper drivers, your computer will not be able to communica...

Bofa debit card activation.

05-20-2023 12:49 PM. Product: HP ENVY Photo 7855 All-in-One Printer. Hi, I have an HP Envy 7855, and like others, have tried all of the suggested and/or recommended troubleshooting steps. I use this printer for work & am not in a position to purchase another one.Product: HP OfficeJet Pro 8720 All-in-One Printer Operating System: Microsoft Windows 10 (64-bit) My printer is stuck on initializing with new cartridges after oobe reset.To keep an HP printer from going offline, move it closer to the router when connected to a wireless network. Alternatively, use a network cable that fits firmly into the printer an...Sep 20, 2021 ... #Hp laserjet 1536dnf mfp stuck on 5 arrow not initialize orange led flash error fix 100% follow. 1.5K views · 2 years ago ...more ...

Create an account on the HP Community to personalize your profile and ask a question. ... When I start up my printer it gets stuck on the "initializing" screen. I have tried hard rebooting it, unplugging it, plugging it into an outlet instead of a power cable, trying a different outlet, updating the driver, and resetting the network/ router. ...11-11-2020 10:12 AM. Product: hp office jet pro 8710. Operating System: macOS 10.13 High Sierra. My office jet pro 8710 printer is stuck on 0% initializing. HP Smart program on computer says printer is connected and everything looks good until I try to print and it says "Cannot print. Connect printer to updte HP instant ink status."Hello there, Our Color Laserjet Pro MFP M176n is stuck at initializing since the last time the yellow toner cartridge has been replaced. After the replacement of the cartridge, the toner carousel turned, started making loud clicking noises and then stopped.Nov 11, 2015 · Please go through the steps in this document to make sure everything setup properly. Here is the link: Setting Up the Printer Hardware for HP Color LaserJet Pro M177fw MFP Printers. You can manually move the carousel for the toners, if it is stuck. Open the scanner lid and the lid below that so you should see the toners. Upon start up, as soon as the screen shows the HP logo (at this point, in black and white), press and hold, in the touch screen area only, the area just above the question mark, until the "...init" prompt appears, then release. This reset procedure will reboot the printer and take it back to READY state. larreaza. 6 0 0.Next, power OFF the printer, remove any/all toner/drum cartridges and power ON the printer. See what message (s) it gets. If it's still stuck on Initializing, you may need to reset the NVRAM or maybe even replace the formatter. If it shows to install/replace the toner/drum cartridge, begin replacing the item requested and closing the access door.New member. 08-26-2022 01:34 PM. My 7155 printer display screen shows that the printer is stuck in initialization/startup mode. I've tried all the posted solutions about disconnecting the power cord from the outlet and/or printer, waiting for extended periods of time, holding down the power button, then reconnecting the cord. None of these work.01-21-2019 01:17 PM. Product: Laser Jet 600 M602. Operating System: Microsoft Windows 10 (64-bit) My work network printer LaserJet 600 M602 is stuck on initializing. I can print to it but I cannot do anything in the menu window. The only way to power down the printer is by removing the power cord from the printer.Product: HP Laserjet Pro M225. Operating System: Microsoft Windows 7 (64-bit) My printer is stuck on "Initializing" and I have tried every solution I can find on the forum. 1) Tried hard reset (unplugging all cords, holding power button); 2) tried removing toner then unplugging; 3) tried holding power button, left arrow and cancel until ...

My HP M1005 MFP Printer showing initializing only. so please help me to solve this issue Best Regards Dasharath Nishad - 7500210

HP M477 fdw, stuck on Initializing i have replaced. Scanner, formatter board Permanent initialized and no luck any help will be highly appreciated - 9004638 ... Check out this link: HP printer is offline or unavailable. Jljesus3. 1 0 0 54 New member ‎02-27-2024 12:01 PM. HP Recommended. Mark as New; Bookmark; Subscribe; Permalink; …Please go through the steps in this document to make sure everything setup properly. Here is the link: Setting Up the Printer Hardware for HP Color LaserJet Pro M177fw MFP Printers. You can manually move the carousel for the toners, if it is stuck. Open the scanner lid and the lid below that so you should see the toners.Reset the printer. With the printer turned on, disconnect the power cord from the rear of the printer. Wait at least 60 seconds. Reconnect the power cord to the rear of the printer. Turn ON the printer, if it does not automatically turn on. Wait until the printer is idle and silent before you proceed.When the HP Scitex FB500 or FB700 printer is powered on, there is normally a short display of low-level computer information before the printer software ...Jan 5, 2020 · If your printer has a network or wireless connection, leave it connected. - Remove the ink cartridges from the printer. - With the printer turned on, disconnect the power cord from the rear of the printer and from the wall outlet or power strip. - Wait at least 60 seconds. - Plug the power cord back into the wall outlet. Learn how to fix firmware update issues on HP LaserJet printers when the control panel is stuck on an error screen. Chapters:00:00 Introduction00:19 Connect ...Be alert for scammers posting fake support phone numbers and/or email addresses on the community. If you think you have received a fake HP Support message, please report it to us by clicking on "Flag Post". Solved: Printer stuck at the initialization screen for several hours. The number under the progress bar continues to rise.My printer is stuck on the "Initializing..." stage, I have tried everything on the forums for info on how to to undo this problem with no success. I contacted a customer support agent with hopes on solving my problems but ended up no where. Hoping for some solutions I haven't tried yet. Tags: hp color laserjet pro mfp m477fnw.Product: Laserjet pro mfp m225dw. Operating System: Microsoft Windows 10 (64-bit) After a reboot, my printer is stuck in the initializing screen. The first time this issue happened it took days to resolve on its own. This time it has been days and it is still not working. I've tried rebooting it.

Taylor tomlinson mom.

Bul armory sas ii.

Yes No. davidzuts. 7,130 918 558. Level 13. 11-13-2014 05:16 PM. I have seen the 94% issue and it can be many things. Best thing to do is remove all paper, remove printheads and ink cartridges. Now start the printer and see if it comes to where is asks for the ink item first and then for the paper.996. Level 1. 12-14-2020 10:30 AM. Product: mfp 127. Operating System: Microsoft Windows 10 (64-bit) not a new printer works great until yesterday will not complete initialzing and therefore will not print. Not able to access the set up simply. Tags: MFP 127.With the printer turned on, disconnect the power cord from the rear of the printer. Wait at least 60 seconds. Reconnect the power cord to the rear of the printer. Turn ON the printer, if it does not automatically turn on. Wait until the printer is idle and silent before you proceed. Note: HP recommends connecting the printer directly to a wall ...First, printer screen is blue with hp logo. Then it briefly turns purple while the green ready light and orange exclamation point flash. Next it says Initializing while the two lights continue to flash. Then the Ready screen appears briefly then it says printing and sounds like it is printing but no paper comes out. Then it starts all over again.Welcome to the HP support community. I understand that your printer screen is stuck, I am glad to assist you. You might have to perform an NVRAM reset on the printer to fix this issue. The reset instructions are specific for your printer and performing those steps on a different printer may brick the device.2) Remove all of your toner cartridges from the printer and close the door. 3) Remove the power cord from the back of the printer (Do no press the power button) 4) Plug the power cord back into the printer. 5) Wait for the printer to turn on completely, then install the toner cartridges.Sep 1, 2021 · This is what I have tried: -unplugging the printer for various amounts of time, for up to 5 minutes before plugging in again. -held down the power button while plugging it in. -using HP print and scan doctor, it fails to communicate with the product, with and without USB cable. Aug 11, 2020 · 4 0 1. Level 1. 08-12-2020 02:51 PM. Well found the problem, connector J606 on the DC Controller, the ribbon cable was kinked. This caused the unit not to produce a engine test and caused the unit to stay in initializing. Thanks for your input Valsimot. Tags: HP LaserJet Enterprise MFP M632h. Turn on the printer. Wait until the printer is idle and silent before you continue. Disconnect the USB cable from the rear of the printer. If your printer has a network or wireless connection, leave it connected. Remove the ink cartridges from the printer. With the printer turned on, disconnect the power cord from the rear of the printer and ...The laptop has recognized the printer but is stuck in the initializing stage. Things tried: printer was restarted after turned off for 60 seconds. -took out the ink cartridge, unplugged both power cable and usb. Restarted with only the power cable plugged in and waited to put back in the cartridge and usb port. Tags: LaserJet Enterprise M607. ….

Create an account on the HP Community to personalize your profile and ask a question Your account also allows you to connect with HP support faster, access a personal dashboard to manage all of your devices in one place, view warranty information, case status and more.Jan 21, 2019 · 01-21-2019 01:17 PM. Product: Laser Jet 600 M602. Operating System: Microsoft Windows 10 (64-bit) My work network printer LaserJet 600 M602 is stuck on initializing. I can print to it but I cannot do anything in the menu window. The only way to power down the printer is by removing the power cord from the printer. Feb 26, 2020 · HP LaserJet M1212nf MFP has been stuck at Initializing screen. I have tried some troubleshooting suggestion through the forums but still not working. I have done: Disconnected the power cable from the printer while the printer is still ON. Disconnected any other cables if connected the printer. Press and hold the printer’s power button for 15 ... Sep 20, 2020 · With the printer turned on, disconnect the power cord from the rear of the printer and also unplug the power cord from the wall outlet. Remove USB cable, if present. Wait for 2-3 minutes, press and hold the power button on your printer for about 30 seconds to remove any additional charge. Now plug back the power cable straight to a wall outlet ... I read your HP LaserJet Pro MFP M225dn Printer is stuck on initialization. I would like to help you resolve this issue. Perform a Hard Reset on the printer. Remove the power cable from the printer when it is turned on. Press and hold the power button for 60secs. Connect the power cable to printer and directly to wall outlet. Turn on the printer.4 0 1. Level 1. 08-12-2020 02:51 PM. Well found the problem, connector J606 on the DC Controller, the ribbon cable was kinked. This caused the unit not to produce a engine test and caused the unit to stay in initializing. Thanks for your input Valsimot. Tags: HP LaserJet Enterprise MFP M632h.We will have to perform an NVRAM reset on the printer that may help. The reset instructions are specific for your printer and performing those steps on a different printer may corrupt the device. I've sent you a private message with reset instructions, follow the reset instruction to perform a full reset and re-initialize the printer.Oct 13, 2021 · Turn on the printer. Wait until the printer is idle and silent before you continue. Disconnect the USB cable from the rear of the printer. If your printer has a network or wireless connection, leave it connected. Remove the ink cartridges from the printer. With the printer turned on, disconnect the power cord from the rear of the printer and ... New member. 08-26-2022 01:34 PM. My 7155 printer display screen shows that the printer is stuck in initialization/startup mode. I've tried all the posted solutions about disconnecting the power cord from the outlet and/or printer, waiting for extended periods of time, holding down the power button, then reconnecting the cord. None of these work.This document is for HP LaserJet Pro 200 color MFP M276n, M276nw, M251n, and M251nw printers. The printer control panel displays Initializing screen, and the printer does not print. Figure : Example of the Initializing screen Hp printer stuck on initializing, [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1]